Computer organization questions and answers. UIC 2019-01-06
Computer organization questions and answers Rating:
5,5/10
438
reviews
Computer Architecture Textbook Solutions and Answers
The address of a page table in memory is pointed by a stack pointer b page table base register c page register d program counter 200. Then, within the body of the loop, the instruction Decrement Rl Reduces the contents of Rl by 1 each time through the loop. The value of S is reduced if instructions have a smaller number of basic steps to perform or if the execution of instructions is overlapped. If k bits are needed to specify the memory address of each operand, the encoded form of the above instruction must contain 3k bits for addressing purposes in addition to the bits needed to denote the Add operation. At the start of execution, all program instructions and the required data are stored in the main memory. Pipelining performance quiz has 15 multiple choice questions. The organization will have its own website which can be researched and the careers and about us section can be read through.
Top 21 Computer Architecture Interview Questions & Answers
Finally, it's easier to write powerful optimized compilers. Each full adder requires three levels of logic. Branch and shift address D. The term was coined to contrast to the old term hardware meaning physical devices. Talk about your previous job and the technical aspects that you have handled. State the differences between a scalar and a vector processor? A single two-address instruction cannot be used to solve our original problem, which is to add the contents of locations A and B, without destroying either of them, and to place the sum in location C.
Though it may be usual, it is important to answer the question carefully. A full adder adds binary numbers and accounts for values carried in as well as out. An answer to this type of question can be framed keeping in mind certain objectives related to your personal self: 1. Hence, the value of S is the total number of basic steps, or clock cycles, required to execute an instruction. What are the total number of clock cycles required to execute the program? Which of the following is not a weighted code? Pauls Engineering Collage Pauls Nagar, Villupuram Tamilnadu, India. This seems to imply that complex instructions combined with pipelining would achieve the best performance.
A pipeline is like ………………. Programmers use organizations called data structures to represent the data used in computations. Using a higher- frequency clock increases the value or R, which means that the time required to complete a basic execution step is reduced. However, the actual timing signals that govern the transfers are generated by the control circuits. In some assembly languages, this mode is called Direct. Data to be used as operands are also stored in the memory. Embedded systems quiz has 21 multiple choice questions.
In the Load instruction, address A specifies the source operand, and the destination location, the accumulator, is implied. The operating system is the most important type of system software in a computer system. Ans: B 102 A page fault A Occurs when there is an error in a specific page. Application software Application software is developed to perform in any task that benefits from computation. Until the outcome of the conditional branch is known the process does not fetch the new instruction. The third port allows the data on bus C to be loaded into a third register during the same clock cycle. The answer to this technical question is to check the basic cable connections.
30 Common Interview Questions and Answers for IT Support
This is a tremendous speed for a mechanical device but is still very slow compared to the electronic speed of a processor unit. This is one of the most common interview questions and the very first question asked in any job interview. Associative Memory Ans: D 116. More than one word is put in one cache block to a Exploit temporal locality references in a program b Exploit spatial locality references in a program c Reduce miss penalty d All of these 2. C Occurs when a program accesses a page not currently in main memory. You also find all interview questions at link at the end of this post.
Thus, the Autoincrement mode is written as Ri + As a companion for the Autoincrement mode, another useful mode accesses the items of a list in the reverse order: 8. Your career is of utmost importance to you. There are three types of interrupts that can cause a break. Write Through technique is used in which memory for updating the data A Virtual memory B Main memory C Auxiliary memory D Cache memory Ans: D 24. Define the layout for instruction sets? Individual condition code flags are set to 1 or cleared to 0, depending on the outcome of the operation performed.
Computer Architecture Textbook Solutions and Answers
Researching about the company before going for an interview is important. What are the attractive aspects and unattractive aspects that you consider about the position? Many other kinds of input devices are available, including joysticks, trackballs, and mouses, which can be used as pointing device. A common convention is to use the sharp sign in front of the value to indicate that this value is to be used as an immediate operand. Cause of busy I work in my home so, I need a high-configaration which is one of the best computers. Memory instruction multiple data D. How can hazards be controlled? To reduce N, we need to have a suitable machine instruction set and a compiler that makes good use of it. The loop is a straight-line sequence of instructions executed as many times as needed.
